Recently listed

Pressure screen:

type: M 60

manufacturer: Ahlström

year of manufacturing: 1986

Was used as 4 . step in approach flow system

Into the machine suit the Voith size 10 screen baskets

Installed is a bump rotor

Made in stainless steel

Tissue paper machine for creped tissue paper.

This machine produce for example handtowels. It is equipped with a very good Pama headbox.

The last safety test By Tüv was 2010

Grammage starting at 30 GSM

Manufacturer: PAMA
Year: 1958
In production until mid of 2010,

now well preserved (cylinders open for avoiding moisture accumulation, lubrication verified, etc...)
Right hand drive
Production: 30-40 tpd
Type of furnish: waste paper
Width at reel: 2320 mm
Speed on Yankee: 320-350 m/min
Yankee diameter: 3187 mm, metallized in 2001
Yankee operating pressure: 2.5 bar
Press section: 2 presses (1 felt press, 1 yankee)
Dry section: 8 drying cylinders. Canopy hood on the cylinders
Cylinder diameter: 1500 mm
Cylinder operating pressure: 2.5 bar
Steam and condensate system
N° 3 doctor blades
Overhead monorail crane for spool handling

Walkways and stairs

Stock preparation composed of:
N° 8 process pumps
N° 20 cleaners
N° 5 screens
N° 1 deflaker
N° 4 chests
N° 1 vertical agitator

Water treatment system
Vacuum system
Air system
PLC by Siemens (Simatic S7)
Pulper, conveyor belt and refiner not included in the supply

Several spare parts available, including cylinders, felts, rolls, motors, screens, etc...

Grey millboard production machine

Grammage range: 1000 - 2000 GSM
Width: 2850 mm
Capacity: 36 t/day

Consisting of
Approach flow system:
1 Voith size 10 pressure screen
1 Finkh vibrating screen
1 Andritz Mixing pump

Board machine:
2 cylinder mould
Coutch roll

Forming section with:
Forming roll: 1500 mm diameter
Pre press roll: 350 mm diameter
Breast roll: 460 mm diameter
Complete with drive, spare rolls

General refurbishment: 1991
Refurbishment: year 2007, Renewing of cylinder mould with couch roll,
Installation of Siemens S7, Framing in stainless steel
Octopus distributor in stainless steel.
Table, working width 3.000 mm
Length: 6.000 mm

Table
Working width: 3.000 mm
Length: 7.000 mm
With guide roll and embossing calander

Table
Working width: 3.000 mm
Length: 5.500 mm

Length cutting unit
Working width: 4.00 mm
Length: 2.500 mm
With water jet cutting

Steam - Flat dryer
Made by: Schilde
Transport with chains
Working width: 4.800 mm
Dryer length: 18.000 mm
With ventilators
Refurbished: 2008

Table
Working width: 4.800 mm
Length: 3.000 mm
Refurbished: 2007

Gas Dryer
Heating power: 1.400 kW
Made by: Dornier
Working width: 4.00mm
Dryer length: 14.000 mm
With heat exchange and heat recovery
Year: 2007

Flat dryer
Hot air drying
Made by: BSH
Working width: 4.800 mm
Length: 25.000 mm
With 5 Drying chambers
Gas burner Ventilators
Heat recovery
Refurbished: 2008

Table
Length cutting device
Made by: Schohr
Year: 1973

2 Hydraulical layboys